Contoh cara mengkonfigurasi VLAN pada cisco packet tracer. Berikut gambar rancangan VLAn yang akan dikonfigurasi.
Pengaturan pada Router 0
Gateway VLAN 10
Router>enable
Router#config term
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#interface fast
Router(config)#interface fastEthernet 0/0.10
Router(config-subif)#encapsulation dot1Q 10
Router(config-subif)#ip address 192.168.100.1 255.255.255.0
Router(config-subif)#exit
Router(config)#exit
%SYS-5-CONFIG_I: Configured from console by console
Gateway VLAN 20
Router#config
Configuring from terminal, memory, or network [terminal]?
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#interface fast
Router(config)#interface fastEthernet 0/0.20
Router(config-subif)#encapsulation dot1Q 20
Router(config-subif)#ip address 192.168.110.1 255.255.255.0
Router(config-subif)#exit
Router(config)#exit
%SYS-5-CONFIG_I: Configured from console by console
Gateway VLAN 30
Router#config
Configuring from terminal, memory, or network [terminal]?
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#interface fast
Router(config)#interface fastEthernet 0/1.30
Router(config-subif)#encapsulation dot1Q 30
Router(config-subif)#ip address 192.168.120.1 255.255.255.0
Router(config-subif)#exit
Router(config)#exit
%SYS-5-CONFIG_I: Configured from console by console
Gateway VLAN 40
Router#config
Configuring from terminal, memory, or network [terminal]?
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#interface fast
Router(config)#interface fastEthernet 0/1.40
Router(config-subif)#encapsulation dot1Q 40
Router(config-subif)#ip address 192.168.130.1 255.255.255.0
Router(config-subif)#exit
Router(config)#exit
%SYS-5-CONFIG_I: Configured from console by console
Pengaturan pada Switch
Switch1
Switch>enable
Switch#vlan database
% Warning: It is recommended to configure VLAN from config mode,
as VLAN database mode is being deprecated. Please consult user
documentation for configuring VTP/VLAN in config mode.
Switch(vlan)#vlan 10 name vlan10
VLAN 10 added:
Name: vlan10
Switch(vlan)#vlan 20 name vlan20
VLAN 20 added:
Name: vlan20
Switch(vlan)#exit
APPLY completed.
Exiting....
Switch#config
Configuring from terminal, memory, or network [terminal]?
Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)#interface fast
Switch(config)#interface fastEthernet 0/1
Switch(config-if)#switchport mode trunk
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to down
Switch(config-if)#
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up
Switch(config-if)#exit
Switch(config)#interface fast
Switch(config)#interface fastEthernet 1/1
Switch(config-if)#switchport access vlan 10
Switch(config-if)#exit
Switch(config)#interface fastEthernet 2/1
Switch(config-if)#switchport access vlan 20
Switch(config-if)#exit
Switch(config)#exit
%SYS-5-CONFIG_I: Configured from console by console
Switch2
Switch>enable
Switch#vlan database
% Warning: It is recommended to configure VLAN from config mode,
as VLAN database mode is being deprecated. Please consult user
documentation for configuring VTP/VLAN in config mode.
Switch(vlan)#vlan 30 name vlan30
VLAN 30 added:
Name: vlan30
Switch(vlan)#vlan 40 name vlan40
VLAN 40 added:
Name: vlan40
Switch(vlan)#exit
APPLY completed.
Exiting....
Switch#config
Configuring from terminal, memory, or network [terminal]?
Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)#interface fast
Switch(config)#interface fastEthernet 0/1
Switch(config-if)#switchport mode trunk
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to down
Switch(config-if)#
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up
Switch(config-if)#exit
Switch(config)#interface fast
Switch(config)#interface fastEthernet 1/1
Switch(config-if)#switchport access vlan 30
Switch(config-if)#exit
Switch(config)#interface fastEthernet 2/1
Switch(config-if)#switchport access vlan 40
Switch(config-if)#exit
Switch(config)#exit
%SYS-5-CONFIG_I: Configured from console by console
Pengaturan IP Configuration pada masing-masing PC
PC0
IP address : 192.168.100.2
Subnet mask : 255.255.255.0
Default gateway : 192.168.100.1
PC1
IP address : 192.168.100.3
Subnet mask : 255.255.255.0
Default gateway : 192.168.100.1
PC2
IP address : 192.168.110.2
Subnet mask : 255.255.255.0
Default gateway : 192.168.110.1
PC3
IP address : 192.168.110.3
Subnet mask : 255.255.255.0
Default gateway : 192.168.110.1
PC4
IP address : 192.168.120.2
Subnet mask : 255.255.255.0
Default gateway : 192.168.120.1
PC5
IP address : 192.168.120.3
Subnet mask : 255.255.255.0
Default gateway : 192.168.120.1
PC6
IP address : 192.168.130.2
Subnet mask : 255.255.255.0
Default gateway : 192.168.130.1
PC7
IP address : 192.168.130.3
Subnet mask : 255.255.255.0
Default gateway : 192.168.130.1
8 komentar:
Thx yo atas infonya...
N ane mau minta izin, numpang promosi nich...
Tolong di coment yah isi blog ane...
http://jaketkuning.unsri.ac.id/panhar/blog/795/
ok. sama2
misi,ikutan belajar
http://jaketkuning.unsri.ac.id/Sigit/blog/775/
kunjungi juga gan http://jaketkuning.unsri.ac.id/rafi/blog/781/
@sigidnino : silahkaaaan. mohon dikoreksi klo ada yg kurang benar.
@rafis : ok. nice!
makasih banyak gan tutorialnya ini sangat bermanfaat buat saya .
kenapa jaringan sisi kiri tidak bisa saling terhubung?
tapi jaringan kanan bisa semua.
Posting Komentar